Locating the Brocade Switch Serial Number When calling for support, use the pictures and information below to first determine the source of your Brocade switch, then locate the Service Tag on a Dell-sourced switch or the serial number on a Brocade-sourced switch. Identify your switch by the information on the pull-out label in the front lower corner of the unit. Dell-Sourced Switches:. Do NOT have any Dell badging. Remove made with a trial copy of smartdraw 2017. Are identified by a label that contains both a Dell Service Tag and a Brocade serial number. Use the 7-character Dell Service Tag for your support request Brocade-Sourced Switches:. Are identified by a label that contains only a Brocade serial number.
Use the 11-character Brocade serial number for your support request.
Alone: standalone, D: dynamic config, S: static config ID Type Role Mac Address Pri State Comment 1 S ICX6610-48 active xxxx.xxxx.xxxx 128 local Ready 2 S ICX6610-48 standby yyyy.yyyy.yyyy 0 remote Ready active standby +-+ +-+ =2/1 1 2/62/1 2 2/6= +-+ +-+ - Standby u2 - No hitless failover. Reason: hitless-failover not configured Current stack management MAC is xxxx.xxxx.xxxx Note: no 'stack mac' config. My MAC will change after failover. Configure the stack to handle switch 'hitless' failure and recovery. Alone: standalone, D: dynamic config, S: static config ID Type Role Mac Address Pri State Comment 1 S ICX6610-48 active xxxx.xxxx.xxxx 128 local Ready 2 S ICX6610-48 standby yyyy.yyyy.yyyy 128 remote Ready active standby +-+ +-+ =2/1 1 2/62/1 2 2/6= +-+ +-+ - Standby u2 - protocols ready, can failover or manually switch over Current stack management MAC is xxxx.xxxx.xxxx Excellent, done.
ICX6430-C12 The ICX6430-C12 doesn't support stacking. However, a stack can be somewhat simulated by tagging a dedicated port with all our VLANs. This will allow traffic from any VLAN to use the same 'uplink' port. Also, without a proper stack, we can not create a trunk/LAG. So we enable rapid STP on each switch's customer-facing uplink port instead. Enable Jumbo Frames The ICX6610 support packets up to 10240. That is to say, if jumbo frames are enabled, the MTU of the switch is 10.
Stack unit 1: Compressed Pri Code size = 5430491, Version:07.3.00jT7f1 (FCXS07300j.bin) Compressed Sec Code size = 6905002, Version:07.3.00fT7f3 (/foundry/FGS/os/FCXR07300f.bin) Compressed Boot-Monitor Image size = 370555, Version:07.3.02T7f5 Code Flash Free Space = 52690944 Stack unit 2: Compressed Pri Code size = 5430491, Version 07.3.00jT7f1 (FCXS07300j.bin) Compressed Sec Code size = 6905002, Version 07.3.00fT7f3 (/foundry/FGS/os/FCXR07300f.bin) Compressed Boot-Monitor Image size = 370555, Version 07.3.02T7f5 Code Flash Free Space = 52690944 Reboot to load the new firmware. Stack unit 1: Compressed Pri Code size = 5430491, Version:07.3.00jT7f1 (FCXS07300j.bin) Compressed Sec Code size = 6905002, Version:07.3.00fT7f3 (/foundry/FGS/os/FCXR07300f.bin) Compressed Boot-Monitor Image size = 370555, Version:07.3.02T7f5 Code Flash Free Space = 52690944 Stack unit 2: Compressed Pri Code size = 5430491, Version 07.3.00jT7f1 (FCXS07300j.bin) Compressed Sec Code size = 6905002, Version 07.3.00fT7f3 (/foundry/FGS/os/FCXR07300f.bin) Compressed Boot-Monitor Image size = 370555, Version 07.3.02T7f5 Code Flash Free Space = 52690944 Done! Configure VLAN provide a way of dividing up a switch (or stack of switches) into multiple, isolated switches (this is actually somewhat simplistic, but it gets the idea across). Traffic from one VLAN segment can not reach ports allocated to another VLAN, providing a useful layer of security.
Brocade San Switch Administrator
Planning We're creating three separate;. ID: 100 for the. ID: 200 for the. ID: 300 for the (. By default, all ports default to 1. If you want to improve security, you can leave all unused ports on VID 1. In this tutorial, we need to allocate all ports for use by other equipment.
Before you start, you need to decide how you want to assign physical ports on your switches to VLAN IDs. I like to do this by creating a table showing all the ports, label their external port numbers and logical numbers and then write in what will be plugged into each port. With this, it's fairly easy to mark what ports will be assigned to what VLANs. Cabling a pair of ICX6450-24 In this example, we're showing how to cable up a pair of switches in a very typical configuration. It can drive two systems along with the usual foundation pack. The table below represents a pair of these stacked together.
The table below represents a pair of these stacked together.
The new European data protection law requires us to inform you of the following before you use our website: We use cookies and other technologies to customize your experience, perform analytics and deliver personalized advertising on our sites, apps and newsletters and across the Internet based on your interests. By clicking “I agree” below, you consent to the use by us and our third-party partners of cookies and data gathered from your use of our platforms. See our and to learn more about the use of data and your rights. You also agree to our.
New License Activations IBM SAN b-type license activations will be performed at the following URL. This site will require registration, which requires a valid email account. When registering, IBM customers may encounter the following on the Create Brocade Account screen. Brocade Partner Network Membership - this is not required. Online Support Tools - again, this is not required. A message that indicates 'Our records show your company's Brocade Partner Network Channel Program approval is pending.' Can also be ignored as it does not impact ability to register.
Once the account is confirmed, the above URL will land directly on the license activation page after logging in. Transfers of Existing Licenses to FRU and CRU Units Additionally, transfers of existing licenses to field replaceable units (FRUs) will require IBM support assistance and can no longer be performed by end users via web site. Customer replaceable units (CRUs) that require license transfers will also require that the customer contact IBM support for assistance. The above is a requirement for license transfers only, Activation of newly purchased licences should not require IBM support assistance.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |